This is a solid aluminum tile formed into a curved fan shape — a decorative interior wall surface rather than a flat square chip pressed onto mesh. Each aluminum tile has a solid body, a straight edge and a flat top face, with one narrow tapered tab at the end. The tab tucks under the next piece as the field is built up, so the wall reads as overlapping scales instead of a grid of straight joints.
The face is matte brushed: fine, lightly grained and satin rather than mirror-polished, so it picks up daylight and interior lighting as a warm metal without throwing glare back across a room. Water beads on the surface instead of soaking into it. Tones across the range run from warm brown and copper bronze through champagne gold and rose gold to a cool gunmetal gray.
It is an interior product, and it is usually specified where a wall is meant to be looked at as much as used: hotel and restaurant interiors, commercial fit-outs, lift lobbies, reception walls, washroom splash walls and residential feature walls. Interior designers reach for it when a ceramic mosaic starts to feel too ordinary. Shopfitters and fit-out contractors like it because awkward details can be solved on site instead of in a workshop. Importers and distributors carry it because the pattern holds a wall on its own without a lighting scheme. It is made in our own aluminum mosaic tile factory and supplied to interior and fit-out teams worldwide.
| Product | TALTF200F aluminum mosaic tile |
| Material | Solid aluminum |
| Tile form | Curved fan shape, interlocking |
| Fixing tab | One narrow tapered tab at one end |
| Top face | Flat |
| Surface finish | Matte brushed |
| Surface texture | Fine, lightly grained |
| Body | Solid, with a straight edge |
| Typical use | Interior decorative wall surfaces |
| Fixing methods | Adhesive bonding, mechanical fixing, dry hanging |
The code identifies the pattern, not the dimension. Piece size, sheet format and the number of pieces per box are confirmed against your wall rather than taken from the code alone, so send us the measured wall area — measure the finished wall, not the drawing — and we will come back with the piece count, the sheet configuration and the number of boxes the job needs.
Mosaic of this type is normally mounted on a sheet or a backing so the spacing stays even across the field, but the mounting for your order should be confirmed with your sales contact before you set out. Plan the setting-out from the centre of the wall and let the cuts fall at the two ends rather than in the middle of a run.
Spacing between pieces follows the way the tapered tab overlaps the next tile, so the joint line is set by the profile rather than by a separate spacer. If the wall runs past a corner or carries a strong pattern, ask for the setting-out to be checked before fixing starts.
The substrate matters more with a fan pattern than with a flat tile, because the profile reads whatever is behind it. The wall should be flat, sound, dry and dimensionally stable, and free of dust, grease and loose material. Tell us what it is built from — plasterboard, render, tile backer board or an existing tiled surface — and we will confirm whether it needs priming, a levelling coat or a different fixing method.
Two things are worth agreeing before the order goes in: the surplus to hold back for pattern alignment, edge cuts and later repairs, and the flatness the substrate has to meet. Keep a few spare pieces from the same batch on site, and confirm the tolerance with your fixer.
Because the order goes straight to the aluminum mosaic tile factory, the piece count, sheet format and box quantity are settled against your measured wall rather than against a standard pack.
| Supply basis | Wholesale aluminum mosaic tiles, single codes or a mixed range in one order |
| Manufacturer | Aluminum mosaic tile factory; orders are placed directly with our sales team |
| Lead time | Custom orders: 30 days |
| Packing | Confirmed against your order and destination |
| Payment terms | Confirmed with your sales contact |
| Shipping terms | Confirmed with your sales contact |
| Order quantity | Confirmed against your code mix and destination |
| Samples | Ask your sales contact about sample availability |
| Mosaic code range | SALCH63W, TALWA120F, SALJFS, SALJF120F, SALWA35F, SAL22V, SALWA120U, SALJF70Y, SALH24W, SALJF46Z, SAL108W3, SAL14WE, SALJF8 |
| Location | Suitable for this product | What to confirm |
| Bathroom wall behind a basin, a mirror or a vanity | Yes | Keep the room ventilated, make sure the substrate is dry before fixing, and wipe splashes down as part of routine cleaning. |
| Kitchen splash zone behind a worktop | Yes | Confirm the fixing method for the wall build-up, which often differs over an existing tiled or painted splashback. |
| Fully tanked shower enclosure | Confirm before specifying | Send the enclosure size, the substrate and the waterproofing detail; setting-out and fixing method are agreed together. |
| Covered balcony, atrium or internal wall next to glazing | Depends on exposure | Say whether rain or driven damp can reach the wall at that position — the aluminum tile is an interior decorative finish, not exterior cladding. |
| Open exterior façade, rainscreen or exterior wall cladding | No | Exterior panels and façade systems come from our board range; this mosaic is not supplied for exposed outdoor work. |
| Wall carrying a fire-rating requirement in the submission | No | The mosaic is a decorative interior finish and is not offered as a fire-rated panel. Raise that requirement with your sales contact at enquiry stage rather than after approval. |
CERSAIPANEL is the brand of Yulin Keli Keying Technology Co., Ltd., a building-material manufacturer established in 2016 and based in Yulin, Shaanxi, where we run our own production base with a workforce of 140. Manufacturing and export sit under one roof, so buyers in Europe, North and South America and Australia deal directly with the people who make the goods. Our full range is backed by third-party testing and the international certifications the company holds, and we take on OEM work and custom orders, from first sample through repeat production.
Yes. Solid aluminum with a matte brushed finish is a practical choice for the splash zone behind a basin, a shower or a kitchen counter, and it is often used on the lower half of a bathroom wall. Keep the room ventilated, wipe splashes down as part of normal cleaning, and make sure the wall behind is dry before the tiles go on. For a fully tanked shower enclosure, confirm the setting-out and the fixing method with your sales contact.
No — this is an interior decorative finish, and the metal mosaic range is not supplied as exterior cladding. Exposed façades, rainscreen work and exterior wall panels are covered by our board range instead. If you are working on a covered entrance, an atrium or an internal wall close to a window, tell us about the exposure and we will say whether the mosaic suits that location.
Yes. Each piece is solid aluminum rather than a thin metal facing bonded to a backing board, which is why a trimmed edge stays crisp and why the piece keeps its form in the hand. The top face is flat, and the profile carries one narrow tapered tab at the end that locks it to the next piece.
The joint line comes from the tile itself — the tapered tab overlaps the neighbouring piece, so the spacing follows the profile rather than a spacer. What matters is the first course: set it out true from the centre of the wall and the rest of the field follows. Send the wall dimensions and the code you are working with, and the setting-out can be checked before fixing starts.
A ceramic mosaic is a flat chip laid on a straight grid, and its pattern usually comes from a glaze or a print. This is a shaped metal piece: the fan profile and the overlapping tab build the pattern physically, and the brushed aluminum face shifts with the light across a wall instead of reading flat. The two are chosen for different effects rather than one replacing the other.
Yes. The codes in the range sit alongside one another, so a scheme can run one pattern over a large field and use a different code on a reveal, a bar front or a panel behind a reception desk. Give your sales contact the codes and the wall areas together, so the setting-out and the order can be planned as one job.